FACTORS EFFECTING SELECTION OF
PATTERN MATERIAL
The following factors must be taken into consideration while selecting
pattern materials.
1. Number of castings to be produced. Metal pattern are preferred when
castings are
required large in number.
2. Type of mould material used.
3. Kind of molding process.
4. Method of molding (hand or machine).
5. Degree of dimensional accuracy and surface finish required.
6. Minimum thickness required.
7. Shape, complexity and size of casting.
8. Cost of pattern and chances of repeat orders of the pattern
TYPES OF PATTERN
The types of the pattern and the description of each are given as under.
1. One piece or solid pattern
2. Two piece or split pattern
3. Cope and drag pattern
4. Three-piece or multi- piece pattern
5. Loose piece pattern
6. Match plate pattern
7. Follow board pattern
8. Gated pattern
9. Sweep pattern
10. Skeleton pattern
11. Segmental or part pattern
1. Single-piece or solid pattern
Solid pattern is made of single piece without joints, partings lines or
loose pieces. It is the simplest form of the pattern. Typical single piece
pattern is shown in Fig.
2. Two-piece or split pattern
When solid pattern is difficult for withdrawal from the
mold cavity, then solid pattern is splited in two parts. Split pattern is made
in two pieces which are joined at the parting line by means of dowel pins. The
splitting at the parting line is done to facilitate the withdrawal of the
pattern. A typical example is shown in Fig.
3. Cope and drag pattern
In this case, cope and drag part of the mould are
prepared separately. This is done when the complete mould is too heavy to be
handled by one operator. The pattern is made up of two halves, which are
mounted on different plates. A typical example of match plate pattern is shown
in Fig.
4.
Three-piece or multi-piece pattern
Some patterns are of complicated kind in shape and hence
cannot be made in one or two pieces because of difficulty in withdrawing the
pattern. Therefore these patterns are made in either three pieces or in
multi-pieces. Multi molding flasks are needed to make mold from these patterns.
5.
Loose-piece Pattern
Loose piece pattern is used when pattern is difficult for
withdrawl from the mould. Loose pieces are provided on the pattern and they are
the part of pattern. The main pattern is removed first leaving the loose piece portion
of the pattern in the mould. Finally the loose piece is withdrawal separately
leaving the intricate mould.
6. Match plate pattern
This pattern is made in two halves and is on mounted on
the opposite sides of a wooden or metallic plate, known as match plate. The
gates and runners are also attached to the plate. This pattern is used in
machine molding. A typical example of match plate pattern is shown in Fig.
7. Follow
board pattern
When the use of solid or split patterns becomes difficult, a contour corresponding to the exact shape of one half of the pattern is made in a wooden board, which is called a follow board and it acts as a molding board for the first molding operation as shown in Fig.
8. Gated
pattern
In the mass production of casings, multi cavity moulds
are used. Such moulds are formed by joining a number of patterns and gates and
providing a common runner for the molten metal, as shown in Fig. These patterns
are made of metals, and metallic pieces to form gates and runners are attached
to the pattern.
9. Sweep pattern
Sweep patterns are used for forming large circular moulds
of symmetric kind by revolving a sweep attached to a spindle as shown in Fig.
Actually a sweep is a template of wood or metal and is attached to the spindle
at one edge and the other edge has a contour depending upon the desired shape
of the mould. The pivot end is attached to a stake of metal in the center of
the mould.
10. Skeleton
pattern
When only a small number of large and heavy castings are to be made, it is not economical to make a solid pattern. In such cases, however, a skeleton pattern may be used. This is a ribbed construction of wood which forms an outline of the pattern to be made. This frame work is filled with loam sand and rammed. The surplus sand is removed by strickle board. For round shapes, the pattern is made in two halves which are joined with glue or by means of screws etc. A typical skeleton pattern is shown in Fig.
11. Segmental pattern
Patterns of this type are generally used for circular castings, for example wheel rim,gear blank etc. Such patterns are sections of a pattern so arranged as to form a complete mould by being moved to form each section of the mould. The movement of segmental pattern is guided by the use of a central pivot. A segment pattern for a wheel rim is shown in Fig.
------------------------
Comments
Post a Comment